2014 Latest Pass4sure&Lead2pass Cisco 642-732 Practice Tests (81-90)

QUESTION 81
If you are calibrating for 2.4 GHz and the site will not be using 802.11 and 802.11b data rates, what should be done to ensure an accurate calibration?

A.    Make sure that the access points have the unused rates disabled.
B.    Make sure that you are using an 802.11b client when calibrating.
C.    Make certain that there are no legacy clients when performing the calibration because they will disrupt the process.
D.    Make sure to use a client that supports both 802.11b/g and 802.11a.

Answer: A

QUESTION 82
What is the basic difference in the manner in which a client location is determined on a map when using Cisco WCS Location v7.0 versus Cisco WCS Base?

A.    Cisco WCS Base uses SNR from two or more APs, and Cisco WCS Location uses the SNR from the closest AP.
B.    Cisco WCS Base uses highest SNR signal from a single AP, and Cisco WCS Location uses highest SNR signal from two or more APs.
C.    Cisco WCS Base uses RSSI from a single AP, and Cisco WCS Location compares the RSSI signal strength from two or more APs.
D.    Cisco WCS Base uses RSSI from two or more APs, and Cisco WCS Location uses RSSI from the closest AP.

Answer: C

QUESTION 83
In evaluating a post-installation WLAN deployment, problems are occurring when a client roams from one AP to another. The client bounces back and forth between APs. Which three items can be checked to resolve this issue? (Choose three.)

A.    When a client roams from one AP to the next, check the client RSSI and SNR levels for both APs at the roaming point.
B.    Simplify 802.1X/EAP by moving from external RADIUS to local authentication.
C.    Verify the authentication being used for the same test that the client would use under production.
D.    Check if the roaming settings in the AP are set properly for non-CCX clients.
E.    Check the RF levels of the first AP as the client moves toward the second AP.
F.    Check that the client roaming parameters are set properly.

Answer: ACE

QUESTION 84
What two factors could cause a post-deployment audit to show a high retransmission rate for the WLAN? (Choose two.)

A.    CRC errors
B.    Rate shifting
C.    CCX compatible clients
D.    High SNR values
E.    High RSSI values

Answer: AB

QUESTION 85
In performing a post-deployment audit, you are concerned by significant changes in measured RSSI and SNR values taken on a wireless client in one location. How do you explain the differences in these values?

A.    The differences in the RSSI and SNR values are a result of signal diffusion in the environment.
B.    The differences in the RSSI and SNR values are a result of multipath in the environment.
C.    The differences in the RSSI and SNR values are a result of signal absorption in the environment.
D.    The differences in the RSSI and SNR values are a result of signal diffraction in the environment.

Answer: B

QUESTION 86
Which tool can best provide throughput verification?

A.    WLC > Monitor > Clients > LinkTest
B.    WaveDeploy
C.    InSSIDer
D.    Xirrus Wi-Fi Inspector

Answer: B

QUESTION 87
Which two types of information should be included in the installation inventory portion of the post- installation report? (Choose two.)

A.    All AP, controller, and MSE administrator credentials
B.    The number and type of all WLAN clients and tags
C.    The names, locations, IP addresses, MAC addresses, etc. for every AP, controller, and MSE in the WLAN
D.    Results of the coverage audit performed with the site survey mapping tool

Answer: AC

QUESTION 88
Which three types of WLAN data, location, and voice testing should be included in the installation customer report? (Choose three.)

A.    Results of the coverage audit performed with the site survey mapping tool per media installed on 802.11a/b/g/n networks
B.    Results of the WCS planning tool
C.    Results from Cisco Unified Communications Manager cluster failover tests
D.    Results of a location readiness test
E.    Results from a WCS WLAN client audit
F.    Results from an ISP throughput test

Answer: ADF

QUESTION 89
Which three types of information should be included in the post-installation customer report? (Choose three.)

A.    VLAN structure and naming convention
B.    Throughput and dB loss for all fiber-optic backbone connections
C.    Naming convention for APs and controllers
D.    Reachability status for all WLAN clients and tags
E.    The number of licenses consumed by clients and tags at installation
F.    Any locations in the WLAN coverage that are secure and require special access

Answer: ACE

QUESTION 90
Which three components make up a Statement of Work? (Choose three.)

A.    Post-survey recommendations
B.    WLAN testing information
C.    A list of changes in scope
D.    Survey type
E.    A list and description of locations to be surveyed
F.    Confirmation of timeline and cost
G.    A list of equipment required to perform network analysis

Answer: DEF

If you want to pass Cisco 642-732 successfully, donot missing to read latest lead2pass Cisco 642-732 exam questions.
If you can master all lead2pass questions you will able to pass 100% guaranteed.

http://www.lead2pass.com/642-732.html